computer HARDWARE BASICS
MICROPROCESSOR:
Microprocessor is the brain of any computer. It controls all activities inside the computer. Basically it performs 2 types of operations - arithmetic & logical operation (internally), read & write (externally). Read /write operations are performed on 2 types of devices - I/O and memory devices. It uses the address bus to select any location on these devices, sends a read/write signal over the control bus and then the information over the data bus.
MEMORY devices:
The CPU stores all information in the computers memory. There are two memory types - RAM & ROM
RAM (Random access Memory):
This volatile type is a read & write memory device. This loses its contents when power is shut off.
The types of RAM are
DRAM (Dynamic ram) is similar to a capacitor, as it tends to lose its contents and hence requires to be refreshed. This is the computer RAM.
SRAM (Static ram) Is faster than Dram and doesnt require to be refreshed. This is costly and hence only a limited amount is used as CACHE memory in the computer.
ROM (Read only memory):
ROM can be programmed using a programmer and then it acts as a read only device. This device is used as the textbook for the CPU in the computer and is called ROM BIOS. It stores all the basic information of programming the devices present inside the system as well as the POST (Power On Self Test) sequence. AMIBIOS and AWARD BIOS are the most common ROM BIOS.
The types of ROM are
PROM (Programmable Read Only Memory)
EPROM (Erasable & Programmable Read Only Memory)
FLASH ROM
EEPROM (Electrically EPROM)
EAPROM (Electrically Alterable ROM)
I/O devices:
Apart from passive memory devices, there are certain controllers in the system, which assist the CPU in performing various operations. These are referred to as I/O devices. These devices include Interrupt controller, Timer, Ports, DMA controller, Floppy Drive controller, CRT controller etc.
BUSES & EXPANSION SLOTS:
These are the means through which communication between various devices of the computer takes place and the types are as mentioned below.
ISA (Industry Standard Architecture):
ISA bus consists of a 24-bit address bus and the 16-bit data bus. ISA can support 8MHZ clock speed.
MCA bus (Micro Channel Architecture):
MCA bus is available either in 16 bit or 32 bit versions. It was developed in a new line of computers called the PS/2 (personal system 2). The clock speed is slightly faster (10MHZ instead of 8MHZ).
EISA bus:
EISA has a 32-bit Address and data bus and 10MHZ CLK speed.
VL BUS/VESA LOCAL bus:
It is a 32-bit bus which was positioned local to the CPU and hence its name. Therefore it could support high bus speeds (that of the CPU).
pci bus:
pci has many benefits over other bus types. First of all, it supports 64 bit and 32-bit data paths. So it can be used both for 486 and Pentium based systems. pci can run up to 33MHZ speed and has the advantage of being isolated from the CPU. intel developed this bus.
pcmcia: (PC Memory card International Association):
The pcmcia was first designed for expanding the memory in small, handled computers. PCMICIAS bus width is only 16 bits, but a 32-bit version is on its way. There are three types of cards namely
Type 1 (3.3 m thick)- used for memory card.
Type 2 (5 mm thick)- used for modem and lan adapter.
Type 3 (10.5 mm0 thick) - used for most common applications like PC hard disk cards.
add ON cards:
These are cards plugged on to the main board, the mother board (The one that houses the CPU & RAM/ROM Bios). Each performs specific functions of interfacing the Motherboard to peripheral device like mouse, monitor etc. Some add-ons are discussed below.
DISPLAY adapter:
These interface the motherboard with the monitor and there are several types of cards. The variations are in resolution, no. Of colors supported and speed.
CGA (Color Graphics Adapter)
640 X 200 pixels
MDA (Mono Display Adapter):
80 characters wide 25 lines long
EGA (Enhanced Graphics Adapter):
640 X 350 mode
VGA (Video Graphics Adapter):
Advanced versions of SVGA/TVGA which start from a resolution of 640 X 480 pixel
AGP (Accelerated Graphics Port):
Introduced in the celeron/P II based systems, this caters to the demanding multimedia applications with its high performance.
IDE I/O card:
Supports the following functions.
SERIAL PORT:
communication external to the computer is done serially (bit after bit) through this port. It is used to connect communication devices like mouse, modem etc.
PARALLEL PORT:
8 Bit data transfer takes place between the computer and an external device. It is typically used to connect a printer.
GAME PORT:
It is used to connect a joystick for playing games.
IDE (Integrated/Intelligent Drive Electronics) Interface: This interface is used to communicate with IDE Hard disks.
FLOPPY DISK controller:
The FDC can support up to two floppy disk drives. The FDC is connected to the system bus and to the DMA controller. It performs data transfer in DMA mode.
sound card:
This is the card that adds audio effects to the computer by providing interface with microphone and speaker. This is used in multimedia computers.
PERIPHERAL devices:
FLOPPY DRIVES:
1.44 MB & 1.2 MB are two types of popular Floppy Drives.
HARD DISK DRIVES:
ST 506 & ESDI are old types. IDE hard disks are popular because their price to performance ratio is very good. For very high performance, SCSI (Small computer systems Interface) is the ideal option, if price is not a criterion.
CDROM DRIVES:
CDROM drive is used in a multimedia system as it can support all types of CD ROMs be it data CD, audio CD, video CD. It has a great advantage of storing about 650 MB of data in a single CD.
keyboard:
keyboard translates the keystrokes into letters or numbers. These letters are interpreted and the computer CPU depending executes commands on what was sent. Variations in terms of XT/AT, no. of keys, type of keys used may be observed.
mouse:
To interact with the pictures (ICONS), a special pointer device was introduced into the computer world. This device is known as mouse and is connected to the serial port.
The mouse contains a round ball that makes contact with two rollers-one for X-axis (the horizontal) and one for Y-axis (the vertical). Moving the mouse causes the ball to roll, and the ball, which is in contact with the two rollers, causes them to turn. This is used for moving clicking the mouse buttons makes a pointer head on the screen and selection.
SCANNERS:
In addition to keyboards and pointing devices, there is another very common method of getting data into the computer. A scanner is used to scan an image (say from a photo) and editing may be done using a suitable software.
MONITORS:
The monitor receives video signals from the computer video adapter card and displays the video information as pixels (picture elements) on the monitor screen. A variety of monitors ranging from CGA mono to SVGA colour are available for users to choose from (though the former is totally obsolete).
CONFIGURATION SETUP:
This is where we define the system configuration. This is done only when the system is assembled and configured for the first time or when it is upgraded. (One may enter the SETUP by pressing Del key as the system is powered up). Different BIOS support different options but the most essential ones, which are found on all systems, are listed below.
DATE & TIME: It displays the correct Date & Time. It has to be set when system is first installed.
FLOPPY TYPE:
To define the Floppy drives connected (1.2MB or 1.44MB).
HARD DISK TYPE: To select the Hard disk type (Primary or secondary)
DISPLAY TYPE: Its select the types of video adapter used for the system monitor.
CACHE ENABLE/DISABLE:
This category speeds up the Memory access. (Default value: Enable) and defines presence or absence of cache memory.
QUICK POWER ON SELF TEST: Its speeds up the Power On Self Test after you power up the computer.
PASSWORD setting: This allows you to set the system password.
POWER MANAGEMENT: This category allows you to select the type (or degree) of power saving.
LOADING DEFAULT VALUES:
There are many parameters, which need to be defined in the CMOS setup, and one may not want to do so manually. This option loads certain default values, stored in the BIOS ROM, which have been defined by the manufacturer for optimal system performance.
ENABLE/DISABLE ON BOARD FUNCTIONS:
To enable/disable certain onboard functions like Floppy Disk control etc (This applies only to integrated Motherboards where the add ON functions are integrated on the Motherboard itself).
PNP FEATURES: This category is used to configure the pci bus slots.
IDE AUTO DETECTION: This allows you to detect the IDE Hard drives automatically.
SAVING & EXITING:
This allows you to save the new setting value in the CMOS memory and continue with the booting process.
POST (POWER ON SELF TEST):
This POST firmware is stored in ROM on the motherboard. This POST is a series of a simple program to test and catch faults in different components and circuits. It tests the microprocessor, interrupt controller, PPI, DMA controller, ROM, RAM, peripheral controllers etc.
SYMPTOMS:
In case of error detection during POST, indications like error beeps/error messages helps troubleshoot problems.
speaker:
With the help of speaker error beeps, we can troubleshoot faults. Each fault causes the speaker to emit different patterns of beeps.
DISPLAYED ERROR MESSAGES:
When system is powered on, error message will be displayed on the screen (Floppy disk fail), if the video adapter is functional.
DIAGNOSTIC cards:
The advanced diagnostic add on card captures details of POST sequence and displays a hexa code which may be used for in-depth & accurate diagnosis of a POST problem.
CDROM DRIVES:
A computer CD-ROM drive uses small, interchangeable, plastic-encased discs from which data is retrieved using a laser beam, much like music compact disc. And like a music CD, a computer CD-ROM stores vast amounts of information. This is achieved by using light to record data in a form thats more tightly packed than the relatively clumsy magnetic read/write heads a conventional drive must manage.
The drive is controlled by a software in your PC that sends instructions to controller circuitry thats either a part of the computers motherboard or on a separate board installed in an expansion slot.
How a CD_ROM drive works? A motor constantly varies the rate at which CD-ROM disc spins so that regardless of where a component, called DETECTOR, is located in relation to the radius of the disc, the portion of the disc immediately above the detector is always at the same speed.
The laser projects a concentrated beam of light that is further focused by a focusing coil.
The laser beam penetrates a protective layer of plastic and strikes a reflective layer that looks like aluminum foil on the bottom of disc.
The surface of the reflective layer alternates between lands and pits. Lands are flat surface areas; pits are tiny depression in the reflective layer. these surface are record of the 1s and 0s used to store data.
Lights that strikes a pit scattered. But light that strikes a land is reflected directly back at the detector, where it passes through a prism that deflects laser beam to a LIGHT-SENSING DIODE.
Each pulse of light that strikes the light-sensing diode generates a small electrical voltages. These voltages are matched against a timing circuit to generates a stream of 1s and 0s that can understand.
Author is an MCSE and having more than 8 Yrs. of Experience in networking and system Administration. Has delivered guest lecture in various Indian Colleges. He can be contacted at kkpathak@technetindia.net Web Site: http://www.technetindia.net
Yoga Mats Yoga Music Yoga Mat Bag Myyogasecrets
